Customer: SUN InBev Ukraine, Yantar brewery, Nikolaev. Energy consumption optimization of the compressor units in the Axima ice water chiller by adjusting the discharge pressure setpoint of the evaporative condensers. The setpoint is adjusted depending on the readings of temperature and humidity sensors according to a tabular algorithm (software optimizer). Visualization of the AXIMA unit […]

Read more

Customer: NPP Kholod LLC. Automation system for the cooling system of high-pressure compressors: temperature transmitters – 7 pcs; valve with adjustable position (input 4-20 mA – setting position, output 4-20 mA – actual position); pressure transmitters – 1 pc .; level transmitters (analog) – 2 pcs.

Read more

Customer: NPP Kholod LLC. Software for monitoring of air compressors: Atlas Copco – 5 pcs.; Ingersoll Rand – 1 pc .; Atelier Francois – 3 pсs.

Read more

Customer: NPP Kholod Ltd. Monitoring of refrigeration automation system: display of instantaneous and totalized flow of the refrigerant in numerical and graphical format, export to CSV, warning alarm at high pressure. Measurements stored in non-volatile PLC memory during loss of communication with the computer. Automated time synchronization PC-PLC. Remote control over the local network and […]

Read more

Customer: Carlberg “Slavutich” brewery Installing an inverter on a screw compressor unit SAB 283S with the control system Uisab, within ammonia refrigeration installation, to provide optimal regulation of the compressor capacity (slide, frequency) in terms of energy consumption and wear of mechanisms as well as for optimal collaboration of several compressors of different capacity.

Read more

Customer: NPP Holod Ltd – Sun Inbev Ukraine, Desna brewery, Chernigiv. Upgrade of refrigeration automation system. Added frequency converters Vacon NHS06505A and NHS07305A on screw compressor units in the systems of ethanol and ice water. Updated algorithms of compressor and evaporative condenser queues in order to optimize power consumption and wear of mechanisms.

Read more

Customer: PS Systec Gmbh. Automation system for propane/CO2 refrigeration plant for the network of supermarkets Lidl: 4 chillers with 0-50-100 step compressors; chillers automatically and flexibly switch between 3 modes: cooling, heating and heat-pump; low temperature cold room. consumer: air cooling fancoils – 3 zones, floor grid heating – 4 sections, refrigerated showcases – 5 […]

Read more

Customer: PS Systec Gmbh. Automation system for propane/CO2 refrigeration plant, based on software of a previous project (Roche): 4 chillers – 1 inverter type and 3 step type 0-100%; cooling tower with frequency inverter fan.

Read more

Customer: NPP Holod LLC. Upgrade of automation system of refrigeration plant. New equipment added: liquid separator, plate heat exchangers (2 pcs.), buffer tank and pumps (2 pcs.) of warm circuit, buffer tank and pumps (3 pcs.) of cold circuit; freecooling system: dry cooling tower fans (18 pcs.), ethanol pump, plate heat exchanger. Integration into energy-consumption […]

Read more

Customer: PS Systec — Weska-Futron — Pharmaceutical company “Roche”, Germany. Automation system for propane/CO2 refrigeration plant: 5 chillers (including 1 spare) – 1 inverter and the others step 0-100%; compressor pack with 3 compressors (including 2 spare) – 1 inverter and the others step 0-100%; 5 double pumps with local controllers Wilo Stratos; 2 coldstore […]

Read more

Customer: Slavutich Brewery, Zaporozhye. Development of electrical project documentation and software for automation system of refrigeration installation: piston compressor units – 4 pcs, screw compressors – 4 pcs; evaporative condensers – 2 pcs, water purification system; ammonia pumps – 2 pcs; glycol pumps – 4 pcs; water pumps with frequency control – 6 pcs; liquid […]

Read more

Customer: Holod Ltd – Sun Inbev Ukraine, Rogan brewery, Kharkiv. Upgrade of automation system of refrigeration plant. New equipment added: 2 compressor units York SAB 233E, evaporative condenser Baltimore VXC 1010, ammonia liquid separator and 2 heat-exchangers. Integration into energy-consumption optimization and monitoring system based on iFix SCADA.

Read more

Customer: Johnson Controls Inc. (York) – InBev brewery Yantar, phase 4. Ukraine, Nikolaev. Development of electrical project documentation and software for automation system of refrigeration installation: screw compressor unit SAB 233L (Unisab III – Profibus); evaporative condenser Baltimore VXC-1240 (2 fans, 2 external pumps, external water pan); air purger; liquid receiver; drain receiver; liquid separator; […]

Read more

Customer: Johnson Controls Inc. (York) – Danone-Dnipro Milk Factory – Danone. Ukraine, Kherson. Upgrade of SCADA system for refrigeration installation: added heat pumps Sabroe Heatpac 108S COM001, glycol heat exchangers Thermowave TL0650KDK-1500 – HXP003, 2 glycol pumps Grundfoss TP 150-280/4, two motor valves Danfoss ICM150.

Read more

Customer: PS Systec, Germany, Augsburg. Universal software block to control a group of compressor units: flexible sequence numbers, equalization of running hours, energy consumption optimization (serial and parallel control logic) for continuous (screw) compressors with variable capacity slide position, for compressors with frequency inverters, and for compressors with discrete capacity steps (piston etc). Mixed sequence […]

Read more

Customer: Johnson Controls Inc. (York) – Kiev milk factory #3 Wimm Bill Dann, Kiev. Electrical engineering and software for automation system of refrigeration plant. New equipment added and new software created for the new and the old equipment: 2 chillers PAC 163 HF-A with control system Unisab II and 1 chiller PAC 193 L with […]

Read more

Customer: Sun Inbev Ukraine, Rogan brewery, Kharkiv. Upgrade of automation system of refrigeration unit. Installation of computer monitoring and control system (SCADA). Efficiency monitoring according to data from electrical meters.

Read more

Customer: Sun Inbev Ukraine, Yantar brewery, Nikolaev. Automation system upgrade of glycol refrigeration unit and CCT refrigeration unit. Development and installation of computer monitoring and control system (SCADA). Efficiency monitoring according to data from flow meters, temperature transmitters and electrical meters.

Read more

Customer: Johnson Controls Inc. (York) – Palm oil refinery Delta Wilmar CIS, town of Yuzhny. Software for automation system of refrigeration pant: 2 screw compressor units SAB 151E (control via Profibus), 2 evaporative condensers Baltimore VXC620, air purger, liquid separator, plate heat exchanger, 4 gas analysers Dozor C5-V263 (monitoring via Modbus RTU).

Read more

Customer: Johnson Controls Inc. (York) – Danone-Dnipro Milk Factory – Danone. Ukraine, Kherson. Upgrade of SCADA for refrigeration plant with the purpose of energy consumption optimization. Connect Socomec DIRIS A40 meter via Profibus DP to CPU S7-414 for monitoring of electrical parameters. Install CP Optimizer Sabroe R717 to calculate the optimal discharge pressure setpoint. Alternative […]

Read more

Customer: Johnson Controls Inc. (York) – Danone-Dnipro Milk Factory – Danone. Ukraine, Kherson. Upgrade of SCADA for refrigeration plant with the purpose of energy consumption optimization. Connect Socomec DIRIS A40 meter via Profibus DP to CPU S7-414 for monitoring of electrical parameters. Install CP Optimizer Sabroe R717 to calculate the optimal discharge pressure setpoint. Alternative […]

Read more

Customer: SABMiller – Kaluga Brewing Company. Russia, Kaluga. Upgrade of SCADA system for refrigeration plant. Modification of compressor sequence algorithm to provide the optimal load with the consideration of compressors’ power. Efficiency monitoring of ammonia refrigerating system according to data from flow meters, temperature transmitters and electrical meters.

Read more

Customer: Khaldotechnika – Kaniv butter-cheese factory – “Cheese Club” Corporation. Ukraine, Kaniv. Upgrade of SCADA for refrigeration plant, added: 2 freon chillers CIAT LWN2800, 2 air condensers, 4 glycol and water pumps, 2 heat-exchangers. Communication with the chillers over RS485 Modbus network.

Read more

Customer: Khaldotechnika – Kaniv butter-cheese factory – “Cheese Club” Corporation. Ukraine, Kaniv. Upgrade of SCADA for refrigeration plant, added: 2 freon chillers CIAT LWN2800, 2 air condensers, 4 glycol and water pumps, 2 heat-exchangers. Communication with the chillers over RS485 Modbus network.

Read more

Customer: York – BBH “Slavutich” Brewery, Ukraine, Zaporizhia Upgrade of the refrigeration automation system: discharge pressure optimizer installed for energy saving.

Read more

Customer: Johnson Controls Inc. (York) – Desna Brewery (InBev). Ukraine, Chernigov. Added equipment: 2 screw compressor units, 1 ice water pump, 1 heat exchanger.

Read more

Customer: Frost SA – Limpantsis Fruit Centre. Greece, Thiva. Added to phase 1: 1 screw compressor unit type NB-3B, 1 evaporative condenser type VXC-250R with frequency control.

Read more

Customer: Khaldotechnika – Karlovka dry milk factory – “Cheese Club” Corporation. Ukraine, Karlovka village. HMI/SCADA for refrigeration plant: 8 freon chillers CIAT LWN2800, 8 air condensers, 14 glycol and water pumps, 4 heat-exchangers. Communication with the chillers over RS-485 Modbus network.

Read more

Customer: Johnson Controls Inc. (York) – Danone-Dnipro Dairy – Danone. Ukraine, Kherson. Automation of refrigeration system: 2 screw compressor units, 1 double evaporative condenser, 1 liquid separator, 2 ammonia pumps, BUCO ice generator: 1 water pump with frequency converter, 4 water pumps, air compressor, 3 heat-exchanging sections (suction, liquid supply and hot gas valves). Supply […]

Read more

Customer: York – “Slavutich” Brewery – BBH. Ukraine, Zaporizhia. Automation of refrigeration system: 4 piston and 4 screw compressor units, 3 single and 2 double evaporative condensers, 2 liquid separators, 1 heat-exchanger, 8 glycol pumps, 2 ammonia pumps.

Read more

Customer: York – UnisabII to Modbus gateway. Denmark, Hoejbjerg. Russia, KazanOrgSintez. A universal software gateway between York compressor control system Unisab II and a Modbus master. Tested in application for two refrigeration plants: in Russia and Taiwan.

Read more

Customer: York – InBev Yantar brewery. Ukraine, Nikolaev. Added to phase 2: 2 screw compressor units, 1 double evaporative condenser, 2 PHEs, 1 primary and 1 secondary glycol pumps. Complete software re-design. Startup-and-adjustment commissioning.

Read more

Customer: Khaldotechnika – Kaniv butter-cheese factory – “Cheese Club” Corporation. Ukraine, Kaniv. HMI/SCADA for refrigeration plant: 6 freon chillers CIAT LWN2800, 6 air condensers, 11 glycol and water pumps, 4 heat-exchangers. Communication with the chillers over RS485 Modbus network.

Read more

Customer: York – SABMiller – Kaluga Brewing Company. Russia, Kaluga. Automation of refrigeration system. Added new equipment and performed complete refactoring (reprogramming) of the old system. Glycol: 3 Grasso and 1 York screw compressor units, 2 single and 2 double evaporative condensers with 4 external water pumps, 4 PHE chillers, 6 glycol pumps, mixing tank […]

Read more

Customer: Grasso – “Radomyshl” brewery, phase 3. Ukraine, Radomyshl. Added to phase1: 2 piston compressor units, 1 evaporative condenser, 3 ammonia pumps, 1 heat-exchanger for ice-water cooling, 1 oil receiver for automatic oil recovery.

Read more

Customer: Grasso – Gavrylivski chicken poultry, Agromars. Ukraine, Gavrylivka village. Refrigeration automation system: 4 screw compressor units (2 stages), 2 double evaporative condensers, 5 ammonia pumps, 5 glycol pumps, 10 ammonia plate freezers, 6 ammonia fast freezers, 17 ammonia air-coolers, 24 glycol air-coolers.

Read more

Customer: Grasso – InBev “Rogan” Brewery. Ukraine, Kharkov. Added to phase 4: 2 screw compressor units, 1 double evaporative condenser, 1 heat-exchanger, 4 ethanol pumps.

Read more

Customer: Grasso – Ismailia poultry SCADA. Egypt, Ismailia. Refrigeration automation system: 6 screw compressor units in three systems -10, -30 and -40°C, 2 evaporative condensers, 6 primary ammonia pumps, falling film chiller, 21 coldstore rooms (T control, automatic defrosting).

Read more

Customer: GEA Grasso (employed). Cerveceria brewery, Ziemann. Puerto Rico, Mayaguez. Refrigeration automation system: 4 piston compressors, 4 evaporative condensers, 4 ammonia pumps. Profibus communication with central PLC.

Read more

Customer: Grasso – InBev Rogan brewery, phase 4. Ukraine, Kharkov. Added to phase 2: 1 liquid separator with motor valve at liquid injection, 1 PHE, 2 ethanol pumps (1 with frequency control). Updated software for the old equipment (including Ethernet communication). Added to phase 3: 1 screw compressor unit, 1 double evaporative condenser.

Read more

Customer: Grasso – InBev Desna brewery. Ukraine, Chernigov. Added to phase 3: 3 evaporative condensers, 1 liquid separator with motor valve at liquid injection, 3 ammonia pumps. Updated software for the old equipment. Added to phase 4: 2 evaporative condensers.

Read more

Customer: York – InBev Yantar brewery. Ukraine, Nikolaev. Software and electrical modifications of Huppmann/Proleit automation system in order to provide consistent control of ice-water equipment after an extension: 1 York piston compressor chiller, 1 Axima water treatment plant, 1 PHE chiller with 1 inner loop water pump and valve station controlled by Danfoss EKC 361, […]

Read more

Customer: York – Interbrew Yantar brewary, phase 2. Ukraine, Nikolaev. Software engineering, electrical supervision and startup-and-adjustment for refrigeration automation system from phase1 plus: 1 screw compressor unit, 1 double evaporative condenser, 1 Plate Heat Exchanger (PHE), 1 primary and 2 secondary glycol pumps. Electrical supervision and startup for ice-water and air compressor cooling systems.

Read more

Customer: York – Interbrew Yantar brewery, phase1. Ukraine, Nikolaev. Electrical supervision and commissioning of refrigeration automation system: 1 screw compressor unit, 1 double evaporative condenser, 1 Plate Heat Exchanger (PHE), buffer tank, 2 primary and 2 secondary glycol pumps.

Read more

Customer: Grasso – Interbrew Rogan. Ukraine, Kharkov. Rebuilt phase 2: 2 piston compressors, 1 screw compressor unit, 5 double evaporative condensers, 2 plate heat exchangers (PHE), 4 frequency controlled water pumps. Industrial Ethernet.

Read more

Customer: GEA Grasso (employed). Chumporn oil factory, De Smet. Thailand, Chumporn. Refrigeration automation system: 1 DuoPack screw compressor unit, 2 ammonia pumps, automatic oil return, 2 sublimators. Profibus communication with central PLC.

Read more

Customer: Grasso – Interbrew Desna. Ukraine, Chernigov. Rebuilt phase 2: 3 Grasso and 1 York screw compressor units, cooling towers: 3 fans and 3 water pumps, 2 evaporative condensers, 2 ethanol pumps.

Read more

Customer: GEA Grasso (employed). Nestle Svitoch confectionery. Ukraine, Lviv. Refrigeration automation system: 1 DuoPack chiller, 1 cooling tower with 2 fans, 3 water pumps.

Read more

Customer: GEA Grasso (employed). Radomyshl brewery – Ziemann, phase 1. Ukraine, Radomyshl. Refrigeration automation system: 2 piston compressors, 1 evaporative condenser, 2 ammonia pumps, 1 plate heat exchanger, automatic oil return.

Read more

Customer: GEA Grasso (employed). Cherkassy distribution cold-storage warehouse, Frau Marta. Ukraine, Cherkassy. Refrigeration automation system: 2 double stage screw compressor units, 2 evaporative condensers, 3 ammonia pumps, 1 freezing tunnel.

Read more

Customer: GEA Grasso (employed). Interbrew Rogan phase 2. Ukraine, Kharkov. Added to phase 1: 1 screw compressor unit, 1 double evaporative condenser, 1 plate heat exchanger, 2 frequency controlled (Danfoss VLT) water pumps. Two distant PLCs (800m) were connected by means of Industrial Ethernet.

Read more

Customer: GEA Grasso (employed). Interbrew Desna phase 3. Ukraine, Chernigov. Refrigeration automation system: 1 screw compressor unit, 1 evaporative condensers, 1 PHE, 2 water pumps.

Read more

Customer: GEA Grasso (employed). Limpantsis fruit storage base. Greece, Thiva. Number of controlled I/O: 127 AI, 23 AO, 427 DI, 189 DO, 47 Profibus nodes. Refrigeration automation system: 6 screw compressor units in two systems -1 and -11°C, 2 frequency controlled (ABB, Profibus) evaporative condensers, recuperation, 5 frequency controlled primary glycol pumps, 2 water pumps, […]

Read more

Customer: GEA Grasso (employed). Zaporozhie oil factory, DeSmet. Ukraine, Zaporozhie. Refrigeration automation system: 2 frequency controlled (Danfoss VLT) screw compressor units w/o GSC, 2 ammonia pumps, automatic oil return, 2 sublimators. Profibus communication with central PLC.

Read more

Customer: GEA Grasso (employed). Kilargo ice-cream factory. Poland, Gdynia. HMI/SCADA for refrigeration automation system: 3 screw compressor units, 16 coldstore rooms.

Read more

Customer: GEA Grasso (employed). Prosiaczek meat-packing factory. Poland, Gdynia. HMI/SCADA for refrigeration automation system: 7 screw compressor units, 19 coldstore rooms.

Read more